enamel coated steel sheet

what is enamel coated steel sheet?

enamel coated steel sheet is the most important components of enamel assembled tank, use 2 to 4 mm thick steel plate, on the demand of the engineering design process, in the interior and exterior wall of steel plate coated with 2 to 3 layers of enamel coating, after thermal polymerization between the enamel layer and steel plate to form a strong combination is enamel coated steel sheet.

enamel coated steel sheet protective coating formed by this coating can not only prevent the corrosion of the tank, but also have the anti-strong acid, The function of strong base.

The enamel steel plate coating is also highly resistant to abrasion. The coating color is usually green, can you customize the color according to the customer, Coating thickness is 2.5 ~ 4.5mm, The standard coating is applied to the pH value of 3 ~ 11, and the special coating is suitable for the pH value of 1 ~ 14. The coating adhesion is 3450N/cm, which is the same as steel plate, about 200kN/mm, with a hardness of 6.0.

Because enamel coated steel sheet is flexible enamel, it is not cracked when the steel plate is subjected to heavy weight or bending. Out of porcelain. enamel coated steel sheet can be used for organic wastewater anaerobic fermentation and aerobic treatment of reservoir? It can also be used for storage of a variety of liquids and solids, and the service life of enamel steel plate is about 50 years

biogas reactor tank enamel steel plate

enamel coated steel sheet installation

Stacking and hoisting of enamel coated steel sheet.enamel coated steel sheet in addition to the standard plate, involving all kinds of u-shaped plate, Yin (Yang) opening Angle plate, plate, concave and convex plate and other special-shaped plate, after transport to the construction site according to the classification of different varieties, specifications of sheet pile, the construction site to plate must be stacked inside;

When need piled up outside, effective measures should be taken to prevent the rain moisture, when enamel coated steel sheet with reduced packaging, flat tier should not be more than 2 m, stand tall shoulds not be more than 2 layers, and slope Angle should not be more than coincidence.

enamel coated steel sheet without packaging should be the luster of the plate faces to, flat tier should not be more than 10 pieces, put appropriate single pile vertical and tilt Angle should not be more than 150, lifting when using special transportation, lifting and construction process, it is strictly prohibited to random collision plate, no scratching, dirty sheet varnish.

enamel bolted tank manufacturer

Before enamel coated steel sheet installation, the enamel steel plate must be based on the intention of the designer and the owner to determine the row board, draw the platoon drawing and effect drawing, and determine the size and number of each plate. The enamel steel plate is forbidden to open slots or boreholes in the field, and all holes are tested in the field and reserved before the manufacture of enamelled steel plates.

The installation sequence of enamel coated steel sheet (enameled plate) should be carried out from the bottom up, avoiding the text fork operation. When required by the design of building exterior wall waterproof, before installation should repair damage to the outer walls of the waterproof layer in the construction process, in addition to design special requirements, the same enamel steel plate of metope color should be consistent, flat-fell seam width of plate shall meet the design requirements.

The installation quality shall be in accordance with the rules and regulations. The ash powder of the enamel steel plate shall be cleaned and the surface of the hanging parts shall be cleaned. The length of the buckled plate shall meet the design requirements.

enamel assembled tank

When design did not make provisions, stainless steel sprocket and porcelain plate supporting edge length, shorter than enamelled steel bearing edge of aluminum alloy buckle rack 20 a 50 mm, sprocket or pin inserted into the enamel steel depth should comply with the design requirements, sprocket allowable deviation of 1 mm, inserted depth of insertion depth allows for 2 mm, when for the stainless steel pendant, epoxy resin slurry should be put into the slot (hole), full with widgets and joint parts of the porcelain plate, then insert the sprocket or pin.